Wire tree instructions

Rachel Lovejoy has been writing professionally since and currently writes a weekly column entitled "From the Urban Wilderness" for the Journal Tribune in Biddeford, Maine, as well as short novellas for Amazon Kindle. Ming trees are artificial recreations of miniature bonsai trees.

Typically no more than 1 foot tall, true bonsai trees often have branches that grow flat across the top of the tree. Despite their size, they look very old, which is part of the appeal that makes them so valuable to collectors. Making your own wire Ming trees can capture some of the appeal of the real thing without costing nearly as much.

Cut the wire with the wire-cutters into workable pieces about 15 inches long. Prepare about pieces for a thick tree. Pass one end of the wire through three small beads or one large one. Repeat this process for each strip of wire. Center the beads at a mid-point on the wire. Bring the ends of the wires together and twist just below the beads to secure them.

Twist two beaded wires together just below the first twist you made to secure the beads on the first wire you prepared. This is your first branch. Make another branch by twisting together two more beaded wires. Add this to the first set of beaded wires and attach in the same way by twisting them around just below where the last two wires connect.

How to Make a Weeping Willow Wire Tree (with gemstones)

Make longer twists as you move toward the ends of the wire. Repeat this procedure until you have eight branches, each with one to three beads, depending upon what size you are using.

Repeat steps 3 and 4 to create two more clusters of eight branches each. Twist these all together to form the trunk. Leave at least 2 inches of wire at the ends to form the roots. Unravel the ends of the wire and spread them out around the foot of the tree. Stand the tree on the wooden base and bend it to a position you like.

Staple the roots to the base as close to the foot of the tree as possible.Making a wire tree sculpture takes very little time, but the end result is a pleasing gift or display for an office, desk or family room. The materials required are simple, easy to use and safe, making wire trees an excellent project for young children. Adult supervision is still required, however, for this project. Using high-quality materials will help ensure that your sculpture lasts.

Copper wire is a durable material that's easy to work with. Paint the base of your wire tree green or brown and allow it to dry overnight. Dye or paint your cotton balls green for use as leaves and canopy. Allow them to dry overnight. Twist copper wire together to form the trunk of your tree. Make sure the wires form a flat base at one end. Hold several lengths by one end and twist them together to form a barklike appearance. Use 8 to 10 strands of copper wire, depending on how thick you want the tree to be.

Twist smaller bunches of copper wire together to form branches. Attach the branches to the trunk by inserting them with a pair of needle-nosed pliers. This will ensure that they stay firmly in place.

Bend and shape the branches once they're on the tree to create realistic-looking randomness in the shape of your tree. Use a glue gun or strong clear-drying glue to attach the tree and its branches to the wooden base.

Attach green cotton balls to the branches to form a more realistic leafy appearance for the tree. If you don't want to use a glue gun to attach your tree to its base, leave 4 to 6 extra inches at the bottom of the tree trunk and wrap the ends around the base firmly. Bailey Shoemaker Richards is a writer from Ohio.

She has contributed to numerous online and print publications, including "The North Central Review. She holds a Bachelor of Arts in creative writing from Ohio University.

Can you use glycolic acid and vitamin c together

Share It. Things You'll Need. About the Author. Photo Credits.This will show you how to make a beautiful work of art in less than an hour. Almost free to make, this is a great gift idea, or make one for your self.

wire tree instructions

Did you use this instructable in your classroom? Add a Teacher Note to share how you incorporated it into your lesson. Wire I used steel wire I found the other day, but any bare wire works Needlenose Pliers Optional Items Base to mount on I used a rock Gloves recommended on heavier guage wire Decorations and adhesive of some kind if needed.

You want your wire to be at least 8 inches long, that way you have room to twist and bend later. I did it about 14 inches long, I wanted a larger tree. You will need quite a few pieces of wire. It's actualy a good thing if they are varying in length a little.

Just eyeball it as you go, using a previous piece as a judge in length. You're not going for perfection here, I think that's part of why this is so fun.

Well, I'm out of wire, so I guess I'm done I got 21 pieces cut from that ball, not bad. For thicker wire, gloves gome in handy for this. You will get an uneven spiral.

This will be the trunk of the tree. Take your groupings of wire and twist them in a similar fashion to what you did for the trunk. Just like you did on the main branches, split up the wires and twist those groupings. As the groups get smaller, you will start to see a bare tree form emerge. Split and twist until You have single wire branches in the different directions.

Bend your branches in different directions to fill out the desired shape. Now it's time to shape the roots. Not much to it, just apply the same method from the top to the bottom half. Flatten out your roots with your hands or your pliers. At this point, your tree is done. All that is left is a little customization. For this specific tree, I used a flat bottomed rock I think it's granite from the courtyard of my apartment.

All I did was set the tree on the rock, took my pliers and bent the roots around it. I curled them on the bottom so the tree wouldnt scratch whatever furiture it ends up on. I've also used flower pots with sand, bonsai stands, it doesn't really matter.

Pick something that you ant to use and go with it. This tree still felt like it needed something else. I happened to Have a red piece of foil paper from a pack of cigarettes my friend left at my place, so I quickly folded an origami crane and glued it to a branch. You can decorate it however you like. Some Ideas are beads, buttons, soda tabs, even hang your jewelry on it. There you have it. A Metal sculptre that is all your own.

Reply 11 months ago. I might suggest Firemountaingems.Personally, I don't have much experience on these things.

How to Make Wire Trees

The tree of the photo is the first one that I have made, but it don't look bad anyway, just a little bit dusty hehe :P. I would try to fix it somehow. Thanks for looking! Take around 50 meters feet of wire - 26 to 32 gauge is preferable 0,4 milimeters diameter - of the color of your choice. Alternatively, you can use more small beads, like seed beads. In this case, you can put beads per strand. Continue this way of twisting toghether 2 or 3 smaller branches to bigger ones until all your wire have form the three basic big branches of the tree.

Twist the three big branches together to form the trunk. If the wire is thick you will probably need the pliers for do this.

Don't twist until the end. Left about centimeters inches untwisted for make the roots. Now divide each group to two parts of about the same amount of strands. Twist the two parts toghether. Left again some wire untwisted. Now -for each group- put again the two parts toghether and then separate it randomly at two or three different parts of strands.

Each of these two parts you will handle like the "group" of the previous step. The roots are like the branches but you work the the opposite way; then you fused, now you divide.

So continue the same proccess of separating, dividing and twisting to make the root branches as needed or until you use all the wire left. Finishing touches; twist the trunk a little bit harder if needed, cut the extra wire that don't fit in the roots and fix the position of the branches.

You can use something to attach your tree to. A single stone is a good choice. You can use some glue if the roots don't help.

You can also put your tree in a bowl with smaller stones or inside a jar. You can even make a little garden or forest. By using different materials and colors, you can create more elegant, spooky, colourful or bonsai-like trees.

The possibilities are endless. Ele's Follow Message. The tree of the photo is the first one that I have made, but it don't look bad anyway, just a little bit dusty hehe :P I hope that you can understand my english. Step 1 Take around 50 meters feet of wire - 26 to 32 gauge is preferable 0,4 milimeters diameter - of the color of your choice.

Step 2 Using the pliers, cut the wire into strands of centimetres inches long each.How we make a wooly feather tree Making a twisted wool feather tree You will need: 1. Any greens or naturals or fun colors! This will make the small to the medium tree or for the large or jumbo tree you will need a half yard.

It does vary depending on how tight and close you wrap your branches. It must be fabric wrapped to hold the florist tape and wool in place. One roll will do a couple small trees or one large one. Match it up to the wool you are using.

While there are not a lot of choices, we use white for white wool or natural wool and brown for green or funky charlie brown trees! You will need to Sharpen it on one end with a pencil sharpener or sand paper to give your tree a soft point.

Wire cutters to snip wire 7. I numbered my clothespins to help keep track of the branches. After you end with wrapping of the wool on the wire and dot it with glue, you will clip with the pin marked for that size until it is dry.

wire tree instructions

Believe us when we say when your looking at about branches its hard to tell! A ruler for cutting the wire and tearing the strips.

How to Make Wire Trees

A 12 inch one is fine For your Wool The small and the medium tree can be made together out of just a fat quarter. The tree takes almost full fat quarter, but more if you add more branches or wrap tightly. The two fat quarters.

wire tree instructions

It really depends on how tightly you wrap and how many rows of branches you want in the tree. I really like mixing the wools on my trees. Then if you run out you can add another color if needed!

Or if your working with yard long pieces you will have less starting and stopping. Try to keep them as even as you can but do not worry to much about it : Attaching the wool to the wire: Place a drop of glue on the end of one wire and roll it between the last two of the cuts on the very end of the torn strip.

If your using E hold for a second or too till it stays Now wrap the wool tautly down the wire. I find just twirling it will make it layer nicely down the length of the wire.

Dabbing a little glue as you go. Use a clip or a clothespin, with the size number ; to hold while it dries.During these challenging times, we guarantee we will work tirelessly to support you.

We will continue to give you accurate and timely information throughout the crisis, and we will deliver on our mission — to help everyone in the world learn how to do anything — no matter what. Thank you to our community and to all of our readers who are working to aid others in this time of crisis, and to all of those who are making personal sacrifices for the good of their communities. We will get through this together. Updated: February 19, Reader-Approved References.

A wire tree sculpture can be a lovely homemade decoration. You can make your own wire tree sculpture to decorate your home, liven up your office, or even to give as a gift. To create this tree you must prepare the branches, twist the wire, and secure the tree in a container.

Making a wire tree sculpture is an easy way to decorate your home or office. Twist each wire into a cross shape, then twist the wires all together into a tree formation. When you've finished, place the stem of your tree into your plant pot filled with stones so it will sit on your desktop or other surface.

wire tree instructions

For more tips, including how to glue your tree into the pot, read on! Did this summary help you? Yes No. Darlene Roberts. Log in Facebook Loading Google Loading Civic Loading No account yet? Create an account. We use cookies to make wikiHow great. By using our site, you agree to our cookie policy.

Cuny portal

As the COVID situation develops, our hearts ache as we think about all the people around the world that are affected by the pandemicCopper Wire 22 gauge metre Cooking pot or any thing having diameter of 33 cm. Masking tape Wire cutter. Wool gloves just to protect the hand from harshness. Did you use this instructable in your classroom? Add a Teacher Note to share how you incorporated it into your lesson. Wrap the wire around cooking pot. Take it off. Cut from one side. Make it straight. Take only 6 wires.

Measure 15 inches from one side and twist this part. Do this to all rest of the wires. Now grab all the wires together and twist them all together only that 15 inches part. Split for the branches. At first I have make 3 main branches.

Wire Tree Sculpture Tutorial- Step by Step Instructions

Split again and again. Tie the last end with masking tape so they don't open. Now set the direction of main branches. Then start splitting them till the end of corners. Just grab bunch of wire and twist them till the end, don't split them two much they will make mess. Open masking tape from the end.

Asrock legacy boot

Split the wires for roots same as we did for branches. Now twist small portion and take out some wires from both sides and again twist, again take out some wire. Do this till end. Twist the side wires and spit them from the end. Finally move the branches to one side like wind turn them.

Question 6 weeks ago. Question 11 months ago on Step 5.

How to Make Wire Ming Trees

Question 1 year ago on Introduction. I know you will think I am stupid but you said to wrap metres around a pot,how much is that in feet????? Very nice art. Have you every used old piano wire? Reply 2 years ago.

Charging by conduction real life examples

I have no idea. I even did not see the piano wires but I think piano wire are made up of steel and its really hard to bend and twist it.


thoughts on “Wire tree instructions

Leave a Reply

Your email address will not be published. Required fields are marked *